KINOTON KOREA - Products

DSi 2.0 앰프는 하드웨어 요구 사항을 간소화하는 동시에 시스템을 보다 빠르고 쉽게 구축합니다. 또한 단일 JBL 시네마 솔루션에 대해 JBL 시네마 스피커의 전력 요구 사항을 충족하도록 설계되었습니다. D-모델은 추가 처리 하드웨어 없이 Dolby ATMOS와 직접 인터페이스합니다. JBL 시네마 스피커 사전 설정은 구성을 단순화하고, 재생 오디오를 최적화하며, 장비 손상을 방지한다. 모든 DSi 2.0 암페어에는 네트워크 오디오 배포, 몰입형 설치 및 타사 극장 관리 및 영화관 제어 시스템과의 직접 인터페이스용 SNMP 연결이 있습니다. 전력 투자와 미래 대비 시스템을 최대한 활용하고자 하는 영화관 관리자와 통합자는 JBL DSi 2.0 시리즈를 통해 실용적이고 비용 효율적인 패키지를 경험 할 수 있습니다.

Each amp offers 4 channels with bridgeable outputs to easily power JBL’s entire line of cinema speakers
Amplifiers are engineered to meet exact power requirements of JBL cinema speakers, for a single JBL cinema solution
A new amplifier design allows for high power output at 2Ω (SA and MA models), enabling up to 4 surround speakers to be powered by a single channel
D-models interface with Dolby Atmos directly, without the need for additional processing hardware. (Future firmware update required)
Three power ratings are available
-SA4/SA4-D (4 channels): 350W (8Ω)/600 (4Ω)/900W (2Ω)/1,100W (8Ω bridged)/1,800W (4Ω bridged)
-MA4/MA4-D (4 channels): 700W (8Ω)/1,200W (4Ω)/1,900W (2Ω)/2,400W (8Ω bridged)/3,800W (4Ω bridged)
-LA4/LA4-D (4 channels): 1,200W (8Ω)/2,000W (4Ω)/1,000W (2Ω)/4,000W (8Ω bridged)/2,000W (4Ω bridged)
All models feature SNMP and ethernet connectivity for networking and third-party control; SA4-D, MA4-D and LA4-D models add Dante/AES67 connectivity. (Future firmware update required)
All models include a HiQ port to interface with HARMAN Audio Architect control software over a standard TCP/IQ network
Best-in-class, 96kHz/32-bit floating-point processing incorporates FIR filtering, LevelMAX™ limiting, 8-channel parametric EQ, delay settings and more
Crown DriveCore technology replaces hundreds of amplifier parts with a single chip, for superior efficiency and reliability
Built-in JBL Cinema Speaker presets match all JBL cinema loudspeakers; amps are power-matched with JBL cinema speakers for optimal performance and fast system configuration
Recall presets, mute channels, monitor amplifier health and power on and off through a combined GPIO/AUX port
SNMP connectivity allows direct interfacing with third-party theater-management and cinema-control systems
An intuitive front-panel LCD and encoder interface let you configure amplifier settings at the push of a button
Ultra-quiet operation: 51dBA maximum fan noise
All models are standard 19-inch (482mm) 2RU rackmount units
Weight: 23.2 pounds (10.5 kg)
Frequency response: 20 Hz–20 kHz
THD: 0.35%
Power supply: 100–220V +/- 10%, 50/60 Hz
Power connector: Standard IEC type, 320 inlet for detachable connector, 100–240V
Accommodates 10AWG wire

※ The specification of the product is as per the initially registered information and subject to change without notice.

Download

Download

JBLDSi2.0_SpecSheet.pdf